top of page
How to measure your garage door spring(s)
How to replace your spring(s)
$14.99 Value/ FREE pair of cables with every spring order! Enter code at checkout.
7ft high Door --- Enter cables7
8ft high Door --- Enter cables8
Wind-Master Torsion Winding Bars

New from Express Door, our Professional Series Wind-Master Torsion Spring Winding Bars!

These are engineered to help make your next spring replacement a breeze. We started off with 1018 cold-rolled carboned steel and forged it to perfectly encompass the entire hole in your garage door spring cones. These bars are crafted to slide in and out of the cones winding holes with ease, but are also tight enough so that it dramatically decreases the risk of it slipping out when winding. These bars make a great investment when it comes to your garage door adjustments. It is highly recommended that your garage door springs be adjusted every 2-3 years, as torsion springs lose tension over time, causing damage to your operator and racking up costly repairs! 

Wind-Master Torsion Winding Bars

SKU: WB01
$12.95Price
  • Set of 2, THESE WINDING BARS WORK WITH ALL RESIDENTIAL GARAGE DOOR TORSION SPRINGS!

Wire Chart
Garage door parts
We Ship our springs with UPS

Super Fast Shipping on all Spring Orders.

online garage door parts
How to
wire chart
Garage Door Parts Diagram

    WARNING: Torsion springs, extension springs, and other garage door hardware can cause serious injury or death if not handled and installed properly.

 

    Professional installation is recommended. Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Read and understand all instructions before you begin work.

 

    Extension and torsion springs, along with attached hardware, are under extreme tension at all times. All tension must be released from springs before any work is performed.

How to Measure your Torsion Spring

This method of measuring your torsion spring requires you to measure the existing springs.  Use this method if the door worked correctly before the spring(s) broke and the garage door has not been tampered with.  To measure the torsion springs, follow each of the following steps carefully.  If the garage door has two springs measure each spring individually.  It is not uncommon to have two different size springs.  If you prefer a matching set, we can convert a mismatched set to a matching set. You can also always call us at (855) 566-0959.

Step 1 Determine Springs ID (Inside Diameter)

For your broken spring(s) measure the inside diameter of the spring. If the spring is in one piece you can normally find the ID on the cones, P175 for 1 3/4" and P200 for 2". Typically residential springs will have a 1 3/4" or 2" inside diameter.

Step 2 Determine Spring Wind

Most standard residential torsion systems have two torsion springs, one on the  right and left. The Left spring is right hand wound(RHW), and the right spring is left hand wound(LHW). If one spring is broken on your torsion system, we highly recommend replacing both springs.

Torsion Springs
Garage Door Spring Supplier
Garage Door Spring Chart
Step 3 Determine Wire Size

The most efficient way to measure the wire size is to measure 10 coils and then measure 20 coils and compare the measurements to the chart below.  Measure to the nearest 1/16" of an inch.  It is important to make sure there are no gaps between the coils.  Measuring coils that have gaps will give incorrect measurements.

Step 4 Determine Spring Length

When measuring your torsion spring, remember that in order to get a proper measurement the spring must be un-wound. If the  spring is in two parts, unscrew set screws and connect spring ends together to  get a total measurement. Do not include the cones in the measurement.

spring final final fianl.png
Garage Door Parts Near Me
Overhead garage door torsion springs
Springs Wire Size Chart

Please feel free to take a look at our How-To Videos or our Frequently Asked Questions page!

bottom of page