© 2019 Express Door. All Rights Reserved

  • Facebook
  • YouTube

Contact Us

Express Door

366 E 600 N Columbia City, IN 46725

Tel: 260-691-3822

Wholesalegdparts@gmail.com

Wind-Master Torsion Winding Bars

Complete Garage Door Torsion Spring Overhaul Kit

home button.png
How to measure your garage door spring(s)
How to replace your spring(s)
$14.99 Value/ FREE pair of cables with every spring order! Enter code at checkout.
7ft high Door --- Enter cables7
8ft high Door --- Enter cables8

5 YEAR WARRANTY   Not China Imports!

  ***These Springs are Engineered for High Cycle Life.***

Here at Express Garage Door Parts, you are truly dealing with an actual garage door repair company. We repair thousands of garage door springs each year. These springs are the lengths that we carry on all of our service trucks and work on 99% of all the residential garage door models out there. The term "Industry standard" is used in reference to standard garage doors, and if you were to send in pictures of your garage door these springs might be recommended if your door is standard for the industry. If you have not been recommended these springs after sending in a picture of your garage door, we recommend measuring your springs and ordering using our "Right or Left Wind Garage Door Spring" option. The Inside diameters on these springs are also industry standard sizes (1 3/4", 2" common). If you want to be sure you are getting the correct wire gauge you can always scroll down this page to find out how to correctly find your existing springs wire size.

            Need a pair? Click Here!

 

* quick reference (For most Doors, not all models)

 

  9x7 Non-Insulated--> 218

  9x7 Insulated--------> 225

16x7 Non-Insulated-> 2 x 218

16x7 Insulated------>  2 x 225

16x7 Wood Door--->  2 x 243

 

Industry Standard Length Torsion Spring

$29.00Price
Wire
Wind
    Wire Chart

    Super Fast Shipping on all Spring Orders.

     
     

        WARNING: Torsion springs, extension springs, and other garage door hardware can cause serious injury or death if not handled and installed properly.

     

        Professional installation is recommended. Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Read and understand all instructions before you begin work.

     

        Extension and torsion springs, along with attached hardware, are under extreme tension at all times. All tension must be released from springs before any work is performed.

    How to Measure your Torsion Spring

    This method of measuring your torsion spring requires you to measure the existing springs.  Use this method if the door worked correctly before the spring(s) broke and the garage door has not been tampered with.  To measure the torsion springs, follow each of the following steps carefully.  If the garage door has two springs measure each spring individually.  It is not uncommon to have two different size springs.  If you prefer a matching set, we can convert a mismatched set to a matching set. You can also always call us at 260-691-3822.

    Step 1 Determine Springs ID (Inside Diameter)

    For your broken spring(s) measure the inside diameter of the spring. If the spring is in one piece you can normally find the ID on the cones, P175 for 1 3/4" and P200 for 2". Typically residential springs will have a 1 3/4" or 2" inside diameter.

    Step 2 Determine Spring Wind

    Most standard residential torsion systems have two torsion springs, one on the  right and left. The Left spring is right hand wound(RHW), and the right spring is left hand wound(LHW). If one spring is broken on your torsion system, we highly recommend replacing both springs.

    Step 3 Determine Wire Size

    The most efficient way to measure the wire size is to measure 10 coils and then measure 20 coils and compare the measurements to the chart below.  Measure to the nearest 1/16" of an inch.  It is important to make sure there are no gaps between the coils.  Measuring coils that have gaps will give incorrect measurements.

    Step 4 Determine Spring Length

    When measuring your torsion spring, remember that in order to get a proper measurement the spring must be un-wound. If the  spring is in two parts, unscrew set screws and connect spring ends together to  get a total measurement. Do not include the cones in the measurement.

    Please feel free to take a look at our How-To Videos or our Frequently Asked Questions page!